C Source Code Serial Port Communication Tutorial

Download example source code

1. Note: It is not worth trying to code the value into the C source as it will use a non-standard method of programming. Alternatively download winpic800 (look online to download it) and set the device to 12F675, load up the hex file and go to the memory location in winpic800 and type in the last location the value 34 followed by the CAL value you.
2. It appears that you are on Windows, Windows has API calls to open and control the serial port, and using the buffered input and output functions is usually not advised when dealing with the serial port. You may want to take a look at this link for Windows serial port communication.

The ‘transmit' and ‘receive' line on this connecter send and receive data between the computers. As the name indicates, the data is transmitted serially. The two pins are TXD & RXD. There are other lines on this port as RTS, CTS, DSR, DTR, and RTS, RI. The ‘1' and ‘0' are the data which defines a voltage level of 3V to 25V and -3V to -25V respectively.

The electrical characteristics of the serial port as per the EIA (Electronics Industry Association) RS232C Standard specifies a maximum baud rate of 20,000bps, which is slow compared to today's standard speed. For this reason, we have chosen the new RS-232D Standard, which was recently released.

Serial Port Communication Code In C Codes and Scripts Downloads Free. I have enumerated my experience working with MATLAB serial port interfacing features in this article. Bluedoc is a Tool for generating documentation in HTML format from doc comments in source code in C and C.

The RS-232D has existed in two types. i.e., D-TYPE 25 pin connector and D-TYPE 9 pin connector, which are male connectors on the back of the PC. You need a female connector on your communication from Host to Guest computer. The pin outs of both D-9 & D-25 are show below.

About DTE & DCE:

Devices, which use serial cables for their communication, are split into two categories. These are DCE (Data Communications Equipment) and DTE (Data Terminal Equipment.) Data Communications Equipments are devices such as your modem, TA adapter, plotter etc while Data Terminal Equipment is your Computer or Terminal. A typical Data Terminal Device is a computer and a typical Data Communications Device is a Modem. Often people will talk about DTE to DCE or DCE to DCE speeds. DTE to DCE is the speed between your modem and computer, sometimes referred to as your terminal speed. This should run at faster speeds than the DCE to DCE speed. DCE to DCE is the link between modems, sometimes called the line speed.

Most people today will have 28.8K or 33.6K modems. Therefore, we should expect the DCE to DCE speed to be either 28.8K or 33.6K. Considering the high speed of the modem we should expect the DTE to DCE speed to be about 115,200 BPS.(Maximum Speed of the 16550a UART) . The communications program, which we use, has settings for DCE to DTE speeds. However, the speed is 9.6 KBPS, 144 KBPS etc and the modem speed.

If we were transferring that text file at 28.8K (DCE-DCE), then when the modem compresses it you are actually transferring 115.2 KBPS between computers and thus have a DCE-DTE speed of 115.2 KBPS. Thus, this is why the DCE-DTE should be much higher than the modem's connection speed. Therefore, if our DTE to DCE speed is several times faster than our DCE to DCE speed the PC can send data to your modem at 115,200 BPS.

What is NULL MODEM?

Null modem is used to connect two DTE's together. This is used to transfer files between the computers using protocols like Zmodem protocol, xmodem protocol, etc

Figure: Above shows the connections of the Null modem using RS-232D connecter

Above-mentioned figure shows the wiring of the null modem. The main feature indicated here is that the to make the computer to chat with the modem rather than another computer. The guest & host computer connected through the TD, RD, and SG pins. Any data that is transmitted through TD line from the Host to Guest is received on RD line. The Guest computer must have the same setup as the Host. The signal ground (SG) line of the both must be shorted so that grounds are common to each computer.

The Data Terminal Ready(DTR) is looped back to Data Set Ready and Carrier Detect on both computers. When the Data Terminal Ready is asserted active, then the Data Set Ready and Carrier Detect immediately become active. At this point, the computer thinks the Virtual Modem to which it is connected is ready and has detected the carrier of the other modem.

All left to worry about now is the Request to Send and Clear To Send. As both computers communicate together at the same speed, flow control is not needed thus these two lines are also linked together on each computer. When the computer wishes to send data, it asserts the Request to Send high and as it is hooked together with the Clear to Send, It immediately gets a reply that it is ok to send and does so.

The Ring indicator line is only used to tell the computer that there is a ringing signal on the phone line. As we do not have, a modem connected to the phone line this is left disconnected

To know about the RS232 ports available in your computer, Right click on 'My Computer', Goto 'Properties', Select tab 'Device Manager', go to Ports( COM & LPT ), In that you will find 'Communication Port(Com1)' etc. If you right click on that and go to properties, you will get device status. Make sure that you have enabled the port( Use this port is selected).

How to program the Serial Port using C/C++?

There are two popular methods of sending data to or from the serial port in Turbo C. One is using outportb(PORT_ID, DATA) or outport(PORT_ID,DATA) defined in 'dos.h'. Another method is using bioscom() function defined in 'bios.h'.

Using outportb() :

The function outportb () sends a data byte to the port ‘PORT_ID'. The function outport() sends a data word. These functions can be used for any port including serial port, parallel ports. Similarly to receive data these are used.

• inport reads a word from a hardware port

• inportb reads a byte from a hardware port

• outport outputs a word to a hardware port

• outportb outputs a byte to a hardware port

Declaration:

• int inport(int portid);

• unsigned char inportb(int portid);

• void outport(int portid, int value);

• void outportb(int portid, unsigned char value);

Remarks:

C Source Code Serial Port Communication Tutorial Free

• inport works just like the 80x86 instruction IN. It reads the lowbyte of a word from portid, the high byte from portid + 2.

• inportb is a macro that reads a byte

• outport works just like the 80x86 instruction OUT. It writes thelow byte of value to portid, the high byte to portid + 1.

• outportb is a macro that writes value Argument

Minecraft for free for mac download. portid:

• Inport- port that inport and inportb read from;

• Outport- port that outport and outportb write to

value:

• Word that outport writes to portid;

• Byte- that outportb writes to portid.

If you call inportb or outportb when dos.h has been included, they are treated as macros that expand to inline code.

If you don't include dos.h, or if you do include dos.h and #undef themacro(s), you get the function(s) of the same name.

Return Value:

#inport and inportb return the value read

#outport and outportb do not return

For more details of these functions read article from beondlogic.com

Using bioscom:

The macro bioscom () and function _bios_serialcom() are used in this method in the serial communication using RS-232 connecter. First we have to set the port with the settings depending on our need and availability. In this method, same function is used to make the settings using control word, to send data to the port and check the status of the port. These actions are distinguished using the first parameter of the function. Along with that we are sending data and the port to be used to communicate.

Here are the deatails of the Turbo C Functions for communication ports.

Declaration:

bioscom(int cmd, char abyte, int port)
_bios_serialcom(int cmd ,int port, char abyte)

bioscom() and _bios_serialcom() uses the bios interrupt 0x14 to perform various communicate the serial communication over the I/O ports given in port.

Devices, which use serial cables for their communication, are split into two categories. These are DCE (Data Communications Equipment) and DTE (Data Terminal Equipment.) Data Communications Equipments are devices such as your modem, TA adapter, plotter etc while Data Terminal Equipment is your Computer or Terminal. A typical Data Terminal Device is a computer and a typical Data Communications Device is a Modem. Often people will talk about DTE to DCE or DCE to DCE speeds. DTE to DCE is the speed between your modem and computer, sometimes referred to as your terminal speed. This should run at faster speeds than the DCE to DCE speed. DCE to DCE is the link between modems, sometimes called the line speed.

Most people today will have 28.8K or 33.6K modems. Therefore, we should expect the DCE to DCE speed to be either 28.8K or 33.6K. Considering the high speed of the modem we should expect the DTE to DCE speed to be about 115,200 BPS.(Maximum Speed of the 16550a UART) . The communications program, which we use, has settings for DCE to DTE speeds. However, the speed is 9.6 KBPS, 144 KBPS etc and the modem speed.

If we were transferring that text file at 28.8K (DCE-DCE), then when the modem compresses it you are actually transferring 115.2 KBPS between computers and thus have a DCE-DTE speed of 115.2 KBPS. Thus, this is why the DCE-DTE should be much higher than the modem's connection speed. Therefore, if our DTE to DCE speed is several times faster than our DCE to DCE speed the PC can send data to your modem at 115,200 BPS.

What is NULL MODEM?

Null modem is used to connect two DTE's together. This is used to transfer files between the computers using protocols like Zmodem protocol, xmodem protocol, etc

Figure: Above shows the connections of the Null modem using RS-232D connecter

Above-mentioned figure shows the wiring of the null modem. The main feature indicated here is that the to make the computer to chat with the modem rather than another computer. The guest & host computer connected through the TD, RD, and SG pins. Any data that is transmitted through TD line from the Host to Guest is received on RD line. The Guest computer must have the same setup as the Host. The signal ground (SG) line of the both must be shorted so that grounds are common to each computer.

The Data Terminal Ready(DTR) is looped back to Data Set Ready and Carrier Detect on both computers. When the Data Terminal Ready is asserted active, then the Data Set Ready and Carrier Detect immediately become active. At this point, the computer thinks the Virtual Modem to which it is connected is ready and has detected the carrier of the other modem.

All left to worry about now is the Request to Send and Clear To Send. As both computers communicate together at the same speed, flow control is not needed thus these two lines are also linked together on each computer. When the computer wishes to send data, it asserts the Request to Send high and as it is hooked together with the Clear to Send, It immediately gets a reply that it is ok to send and does so.

The Ring indicator line is only used to tell the computer that there is a ringing signal on the phone line. As we do not have, a modem connected to the phone line this is left disconnected

To know about the RS232 ports available in your computer, Right click on 'My Computer', Goto 'Properties', Select tab 'Device Manager', go to Ports( COM & LPT ), In that you will find 'Communication Port(Com1)' etc. If you right click on that and go to properties, you will get device status. Make sure that you have enabled the port( Use this port is selected).

How to program the Serial Port using C/C++?

There are two popular methods of sending data to or from the serial port in Turbo C. One is using outportb(PORT_ID, DATA) or outport(PORT_ID,DATA) defined in 'dos.h'. Another method is using bioscom() function defined in 'bios.h'.

Using outportb() :

The function outportb () sends a data byte to the port ‘PORT_ID'. The function outport() sends a data word. These functions can be used for any port including serial port, parallel ports. Similarly to receive data these are used.

• inport reads a word from a hardware port

• inportb reads a byte from a hardware port

• outport outputs a word to a hardware port

• outportb outputs a byte to a hardware port

Declaration:

• int inport(int portid);

• unsigned char inportb(int portid);

• void outport(int portid, int value);

• void outportb(int portid, unsigned char value);

Remarks:

C Source Code Serial Port Communication Tutorial Free

• inport works just like the 80x86 instruction IN. It reads the lowbyte of a word from portid, the high byte from portid + 2.

• inportb is a macro that reads a byte

• outport works just like the 80x86 instruction OUT. It writes thelow byte of value to portid, the high byte to portid + 1.

• outportb is a macro that writes value Argument

Minecraft for free for mac download. portid:

• Inport- port that inport and inportb read from;

• Outport- port that outport and outportb write to

value:

• Word that outport writes to portid;

• Byte- that outportb writes to portid.

If you call inportb or outportb when dos.h has been included, they are treated as macros that expand to inline code.

If you don't include dos.h, or if you do include dos.h and #undef themacro(s), you get the function(s) of the same name.

Return Value:

#inport and inportb return the value read

#outport and outportb do not return

For more details of these functions read article from beondlogic.com

Using bioscom:

The macro bioscom () and function _bios_serialcom() are used in this method in the serial communication using RS-232 connecter. First we have to set the port with the settings depending on our need and availability. In this method, same function is used to make the settings using control word, to send data to the port and check the status of the port. These actions are distinguished using the first parameter of the function. Along with that we are sending data and the port to be used to communicate.

Here are the deatails of the Turbo C Functions for communication ports.

Declaration:

bioscom(int cmd, char abyte, int port)
_bios_serialcom(int cmd ,int port, char abyte)

bioscom() and _bios_serialcom() uses the bios interrupt 0x14 to perform various communicate the serial communication over the I/O ports given in port.

cmd: The I/O operation to be performed.

portid: port to which data is to be sent or from which data is to be read.

0: COM1
1: COM2
2: COM3

abyte:

When cmd =2 or 3 (_COM_SEND or _COM_RECEIVE) parameter abyte is ignored.

When cmd = 0 (_COM_INIT), abyte is an OR combination of the following bits(One from each group):

For example, if

abyte = 0x8B = (0x80 | 0x08 | 0x00 | 0x03)= (_COM_1200 | _COM_ODDPARITY | _COM_STOP1 | _COM_CHR8)

the communications port is set to
1200 baud (0x80 = _COM_1200)
Odd parity (0x08 = _COM_ODDPARITY)
1 stop bit (0x00 = _COM_STOP1)
8 data bits (0x03 = _COM_CHR8)

To initialise the port with above settings we have to write,

Serial Port Communication Program

bioscom(0, 0x8B, 0);

To send a data to COM1, the format of the function will be bioscom(1, data, 0). Similarly bioscom(1, 0, 0 ) will read a data byte from the port.

The following example illustrate how to serial port programs. When a data is available in the port, it inputs the data and displays onto the screen and if a key is pressed the ASCII value will be sent to the port.

When you compile and run the above program in both the computers, The characters typed in one computer should appear on the other computer screen and vice versa. Initially, we set the port to desired settings as defined in macro settings. Then we waited in an idle loop until a key is pressed or a data is available on the port. If any key is pressed, then kbhit() function returns non zero value. So will go to getch function where we are finding out which key is pressed. Then we are sending it to the com port. Similarly, if any data is available on the port, we are receiving it from the port and displaying it on the screen.

To check the port, If you have a single computer, you can use loop-back connection as follows. This is most commonly used method for developing communication programs. Here, data is transmitted to that port itself. Loop-back plug connection is as follows.

Fig 2. Loop-back plug connection

C Code Serial Communication

If you run the above program with the connection as in this diagram, the character entered in the keyboard should be displayed on the screen. This method is helpful in writing serial port program with single computer. Also you can make changes in the port id if your computer has 2 rs232ports. You can connect the com1 port to com2 of the same computer and change the port id in the program. The data sent to the port com1 should come to port com2. then also whatever you type in the keyboard should appear on the screen.

The program given below is an example source code for serial communication programmers. It is a PC to PC communication using RS232. Download the code, unzip and run to chat in dos mode between two computers. Use the program to get more idea about serial port programming.

Click here to download example source code: pc2pc.zip

Please contact us if any problem exits in the above programs.

>Interfacing Links:Links related to serial port, bioscom function, rs232, rs485, usb, parallel port etc.
>Click here to list other C Programming sites

Click here to send feedback or use email: harsha@electrosofts.com or veena@electrosofts.com

Note: Examples given above are tested with Turbo C++ Compiler Version 3.0. How ever, we do not give any guaranty for working of the programs in the examples.